Mon-Fri: 7AM-8PM, Sat: 8AM-6PM, Sun: 9AM-5PM Licensed & Insured [email protected] Serving Raleigh, NC

Screw Drive Opener Repair in Raleigh, NC

Screw-drive openers cleaned, lubricated and repaired. Typical cost $125-$350.

Garage doors rarely fail at a convenient time. If you need screw drive opener repair in Raleigh, NC, we can often come out the same day when a technician is available. Screw-drive openers cleaned, lubricated and repaired.

When to call for screw drive opener repair

  • The motor runs but the door doesn't move
  • Squealing from the rail
  • Slow or jerky travel, especially in cold weather

What usually causes it

  • Worn trolley or coupler
  • Dry or dirty screw rail
  • Temperature swings affecting the rail

What you can check yourself

  • Look for grime and dried grease along the threaded rod.
  • Only use the lubricant the manufacturer recommends for the screw rail.

Still stuck? Our free symptom checker and troubleshooting wizard walk you through it step by step.

Our screw drive opener repair process

  1. Inspect the screw, trolley and motor coupler
  2. Clean and lubricate the rail
  3. Replace worn trolley or coupler parts
  4. Set the limits and force
  5. Test the opener

Typical screw drive opener repair prices

$125-$350Typical range, parts & labor
about 1 hourTypical time on site

What moves the price:

  • Drive type: chain, belt, screw or wall-mount
  • Whether the fix is a part or a whole new opener
  • Remotes, keypads and smart accessories
  • Ceiling height and rail extensions

These are typical U.S. ranges, not a quote. You get an exact price for your door before any work starts. For a quick estimate, try the repair cost calculator.

Local screw drive opener repair for Raleigh, NC

A closed garage in a North Carolina summer gets very hot, which shortens the life of opener circuit boards, capacitors and photo-eye sensors. Storms add power surges, so a surge protector is cheap insurance.

Technicians serve all of Raleigh (ZIP codes 27601, 27602, 27603, 27604, 27605 and more), plus Garner (4.4 mi), Cary (8.1 mi), Knightdale (8.9 mi) and Morrisville (11.1 mi). Call (833) 435-8883 to book a visit in Raleigh.

Screw Drive Opener Repair: frequently asked questions

How much does screw drive opener repair cost in Raleigh, NC?

Screw Drive Opener Repair typically costs $125-$350 including parts and labor, and usually takes about 1 hour. The exact price depends on your door and the parts it needs, and you get it before any work starts. Call (833) 435-8883 for a quote.

Can you do screw drive opener repair the same day?

Often, yes. When a technician is available we can usually come the same day, and common parts are carried on the truck. Doors that won't close or have a broken spring are treated as priority calls, and emergency service is available.

Is screw drive opener repair covered by a warranty?

Our work comes with a 90-day labor warranty on repairs. New parts and doors also carry the manufacturer's warranty. Ask for the warranty details in writing with your quote.

Are your technicians licensed and insured?

Our technicians are insured, and where North Carolina or Raleigh requires a contractor license for garage door work, the job is done under that license. You're welcome to ask for proof when you book.

Should I repair or replace my opener?

A good rule of thumb: if the repair costs more than about 50% of a replacement, or the opener is near the end of its life, replace it. Most openers last 10 to 15 years. If yours is older than that, lacks photo eyes or rolling-code security, or needs a logic board or motor, a new opener is often better value. Springs are the exception: a broken spring is always replaced, never repaired. Our free repair vs. replace calculator can help you compare.

More services

Popular Garage Door Services in Raleigh, NC

Moore-O-Matic Garage Door Sensor Repair

Moore-O-Matic openers are no longer made. We can often keep one running with available parts, or recommend a modern replacement.

Typical $100-$250

Northwest Door Extension Spring Replacement

Side-mounted extension springs replaced in matched pairs, with safety cables installed.

Typical $150-$350

Richards-Wilcox Garage Door Roller Replacement

Worn steel or plastic rollers swapped for quiet, sealed nylon rollers.

Typical $150-$350

DBCI Roll-Up Door Repair

DBCI makes roll-up doors and hallway systems for self-storage.

Typical $150-$600

Holmes Garage Door Garage Door Installation

New steel, insulated, wood-look and carriage-style doors, measured and professionally installed.

Typical $1,200-$4,500

Martin Door Garage Door Roller Replacement

Worn steel or plastic rollers swapped for quiet, sealed nylon rollers.

Typical $150-$350

Haas Door Garage Door Installation

Haas Door, based in Wauseon, Ohio, makes residential and commercial sectional and rolling doors.

Typical $1,200-$4,500

CHI Overhead Doors Extension Spring Replacement

CHI Overhead Doors builds residential and commercial sectional doors in Arthur, Illinois, and sells them through independent dealers.

Typical $150-$350

Garaga Torsion Spring Replacement

Garaga is a Canadian garage door manufacturer based in Quebec.

Typical $200-$450

Windsor Door Garage Door Cable Repair

Frayed, snapped or slipped lift cables replaced and the door re-leveled.

Typical $150-$350

Wayne Dalton Garage Door Roller Replacement

Wayne Dalton is part of the Overhead Door Corporation. Many Wayne Dalton doors use the TorqueMaster spring system, with the springs sealed inside the torsion tube, so spring work needs TorqueMaster parts and a different procedure.

Typical $150-$350

Midland Garage Door Garage Door Repair

Diagnosis and repair for doors that are stuck, noisy, crooked or won't open or close.

Typical $150-$450

Garage door stuck, noisy or broken?

Talk to a garage door technician in Raleigh, NC now. Tell us what the door is doing and we'll give you a price and an arrival window.

Call NowFree Quote